Posted on Leave a comment

Getting Start with NUTTYFI- An IoT Device Examples

Fundamental Requirements:

To Start with NUTTYFI, You have to NUTTYFI IOT Device & FTDI USB to UART Bridge.

After that Connect NUTTYFI to your Computer using FTDI USB to UART Bridge & got to tools -> boards-> NodeMCU 1.0(ESP-12E Module & Select the Port like COM3.

after that copy these code (codes given below) to your arduino IDE & compile & upload to NUTTYFI & all done.

Download: 

Examples- 

  • How to Blink LED using NUTTYFI?
/**************************************NUTTYFI****************************/
// connect LED Positive pin at D6 of NUTTYFI. Connect Negative pin of LED to GND at NUTTYFI.
const int led = D6;
void setup() {
pinMode(led, OUTPUT); // initialize digital pin 'led' as an output.
} 
// the loop function runs over and over again forever 
void loop() {
digitalWrite(led, HIGH); // turn the LED on (HIGH is the voltage level)
delay(1000); // wait for a second
digitalWrite(led, LOW); // turn the LED off by making the voltage LOW
delay(1000); // wait for a second
}
/*********************************************************/
/**************************************NUTTYFI****************************/
// include the library code:
#include <LiquidCrystal.h>

// initialize the library with the numbers of the interface pins
LiquidCrystal lcd(D2, D3, D4, D5, D6, D7);

void setup() {
// set up the LCD's number of columns and rows:
lcd.begin(16, 2);
// Set the cursor
lcd.setCursor(0, 0);
// Print a message to the LCD.
lcd.print("Hi! Welcome");
}

void loop() {

lcd.setCursor(0, 1);
lcd.print("to NUTTYFI");
lcd.setCursor(12, 1);
lcd.print(millis() / 1000);
}
/*********************************************************/
/*********************************NUTTYFI*********************************/

#include <ESP8266WiFi.h>
String apiKey = "Z55PHKYMUB0QTTE5"; //Change your 'Write API Key' of your thingspeak channel
const char* ssid = "NUTTYFI"; // Change your hotspot/ wifi name here
const char* password = "NUTTYFI@123"; // Change your wifi/ hotspot password
const char* server = "api.thingspeak.com";
WiFiClient client;

const int temp=A0; // Connect your LM35 temperature sensor AOUT pin TO A0 Pin of NUTTYFI.
int LM35_data=0;
String inputString_NODEMCU = "";

void setup()
{
Serial.begin(9600); // Serial Begin at 9600 Baud Rate
delay(3000);
WiFi.begin(ssid, password);
Serial.println();
Serial.println();
Serial.print("Connecting to ");
Serial.println(ssid);
WiFi.begin(ssid, password);
while (WiFi.status() != WL_CONNECTED)
{
delay(500);
Serial.print(".");
}
Serial.println("");
Serial.println("WiFi connected");
}

void loop()
{
// as LM35 sensor gives 10mV Scale Factor to change in one Degree Centegrade,double as compare to Arduino
LM35_data=analogRead(temp)/2;
if (client.connect(server,80))
{
String postStr = apiKey;
postStr +="&field1=";
postStr += String(LM35_data);
postStr += "\r\n\r\n";

client.print("POST /update HTTP/1.1\n");
client.print("Host: api.thingspeak.com\n");
client.print("Connection: close\n");
client.print("X-THINGSPEAKAPIKEY: "+apiKey+"\n");
client.print("Content-Type: application/x-www-form-urlencoded\n");
client.print("Content-Length: ");
client.print(postStr.length());
client.print("\n\n");
client.print(postStr);

Serial.print("Field-1: ");
Serial.print(LM35_data);
Serial.println(" data send");


}
client.stop();
Serial.println("Waiting");
delay(400);// thingspeak needs minimum 15 sec delay between updates

}
/*********************************************************/
/***************************NUTTYFI***************************************/
#include <SoftwareSerial.h>
#include <ESP8266WiFi.h>

String apiKey = "Z55PHKYMUB0QTTE5"; //Change your 'Write API Key' of your thingspeak channel
const char* ssid = "NUTTYFI"; // Change your hotspot/ wifi name here
const char* password = "NUTTYFI@123"; // Change your wifi/ hotspot password
const char* server = "api.thingspeak.com";
WiFiClient client;

const int trigPin = D6;
const int echoPin = D7;
// defines variables
long duration;
int distance;

void setup()
{
Serial.begin(9600);
delay(10);
pinMode(trigPin, OUTPUT); // Sets the trigPin as an Output
pinMode(echoPin, INPUT); // Sets the echoPin as an Input
WiFi.begin(ssid, password);
Serial.println();
Serial.println();
Serial.print("Connecting to ");
Serial.println(ssid);

WiFi.begin(ssid, password);

while (WiFi.status() != WL_CONNECTED)
{
delay(500);
Serial.print(".");
}
Serial.println("");
Serial.println("WiFi connected");
}

void loop()
{
void Ultra_NUTTYFI();
if (client.connect(server,80))
{
NUTTYFI_Ultrasonic_POST();
}
client.stop();
Serial.println("Waiting");
delay(1000);// thingspeak needs minimum 15 sec delay between updates

}

void Ultra_NUTTYFI()
{
digitalWrite(trigPin, LOW);
delayMicroseconds(2);
digitalWrite(trigPin, HIGH);// Sets the trigPin on HIGH state for 10 micro seconds
delayMicroseconds(10);
digitalWrite(trigPin, LOW);
duration = pulseIn(echoPin, HIGH); // Reads the echoPin, returns the sound wave travel time in microseconds
distance= duration*0.034/2; // Calculating the distance
Serial.print("Distance: ");// Prints the distance on the Serial Monitor
Serial.println(distance);
}
void NUTTYFI_Ultrasonic_POST()
{
String postStr = apiKey;
postStr +="&field1=";
postStr += String(distance);
postStr += "\r\n\r\n";

client.print("POST /update HTTP/1.1\n");
client.print("Host: api.thingspeak.com\n");
client.print("Connection: close\n");
client.print("X-THINGSPEAKAPIKEY: "+apiKey+"\n");
client.print("Content-Type: application/x-www-form-urlencoded\n");
client.print("Content-Length: ");
client.print(postStr.length());
client.print("\n\n");
client.print(postStr);

Serial.print("Send data to channel-1 ");
Serial.print("Content-Length: ");
Serial.print(postStr.length());
Serial.print("Field-1: ");
Serial.print(distance);
Serial.println(" data send");

}
class="brush: cpp">
/*********************************************************/

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.